Autopilots

Need to replace a split connector? Our replacement split connector helps you easily route cables during installation and eliminates the need to drill large holes in your boat. WARNING: This product...

Whether you're going for salmon, trout, walleye or some other species or just taking your sailboat out of the marina, your Reactor 40 kicker autopilot can help you maintain heading hold and route to...

Reactor 40 Mechanical/Retrofit/Solenoid Corepack without GHC 20 010-00705-48 The Most Responsive Autopilot System on the Water Solid-state 9-axis Attitude Heading Reference System...

GRF™ 10 - Rudder Feedback SensorCompatible DevicesPair this sensor with the GHP 12™ to provide rudder position feedback and to detect and avoid rudder stops while sailing or boating.The GRF 10 uses a...

Actuator Power Cable10" x 7" x 2" actuator power cable WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other...

CCU Extension Cable 5MMount your CCU farther than 3 m (9.8') away from the ECU with a 5 m (16.4'), 15m (49.2'), or 25m (82.0') extension cable. WARNING: This product can expose you to chemicals...

Rudder Feedback Cable5" x 5" x 1" rudder feedback cable WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other...

CCU Extension Cable 15MMount your CCU farther than 3 m (9.8') away from the ECU with a 5m (16.4'), 15m (49.2'), or 25m (82.0') extension cable. WARNING: This product can expose you to chemicals...

SeaStar Fittings Kit Fittings kit for plumbing your Garmin hydraulic autopilot for most SeaStar steering systems.  What's In The Box? 3 pieces of 1/4” NPT male to marine tube male (3/8” compression)...

Whether you’re going for salmon, trout, walleye or some other species or just taking your sailboat out of the marina, your Reactor 40 kicker autopilot can help you maintain heading hold and route to...

Use this 5 meter interconnect cable to connect your GHP™ Reactor autopilot CCU (couse computer unit) to ECU (electronic control unit). Includes bare wire connections for alarm and optional Shadow...

Extend the length of your compatible 8-pin transducer with this cable.

Use this optional stainless-steel tilt tube to replace the mild steel tilt tube on Yamaha® and Honda outboards. The tube provides corrosion resistance in saltwater or brackish water environments,...

Connect a jog lever to our Reactor 40 autopilots1 on displacement hull boats. Adjust heading hold with the jog lever by pressing it right or left, or put the autopilot into the new Power Steering...

1.2-Liter Pump Kit 010-00705-64 Use Garmin's 1.2 Liter per minute (0.32 gallon per minute) pump kit with your Reactor 40 system to pump hydraulic fluid to the steering cylinders and steer the boat...

2-Liter Pump Kit 010-00705-63 Use Garmin's 2.0 Liter per minute (0.53 gallon per minute) pump kit with your Reactor 40 system to pump hydraulic fluid to the steering cylinders and steer the boat...

Autopilot Check Valve KitThis check valve kit is used with the 1.2L and 2.0L autopilot pumps to isolate them from the steering system when the autopilot is not active. Check valves to prevent slow...

Compact Reactor™ 40 Hydraulic Autopilot Starter Pack 010-00705-06 Ideal Entry-level Autopilot System Includes Compact Reactor 40 CCU, ECU, pump and other autopilot components needed to add to...

Compact Reactor™ 40 Hydraulic Autopilot with GHC™ 50 & Shadow Drive™ Technology Pack with GHC™ 50 & Shadow DriveEvery Captain Needs a Co-Pilot. Designed for boats less than 25’ long, this...

Compact Reactor™ 40 Hydraulic Autopilot with GHC™ 50 Instrument Pack with GHC™ 50Every Captain Needs a Co-Pilot. Designed for boats less than 25’ long, this entry-level, Compact Reactor 40 hydraulic...