Anchoring & Docking

Tiedown Engineering Outside Corner 1.5 26428C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners.

Tiedown Engineering Outside Corner End 26523C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners.

Tiedown Engineering Outside Corner Male W-Tab 26418B. Use with a female outside corner to connect docks end to end. Joint requires 3/4" bolt set (N) or connector pin (O). Each leg is 10"L x 5" H.

Tiedown Engineering Pile Chain Holder 26419For use as a pile holder with 3/8" galvanized chain and shackles. Can be adjusted for various pile diameters.

Tiedown Engineering Piling Hoop 10 26391Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416).

Tiedown Engineering Piling Hoop 12 26394Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416).

Tiedown Engineering Piling Hoop 14 26393Heavy duty 1/4" galvanized steel. 3" high. Can bolt to the dock directly or to an optional deck plate (26416).

Tiedown Engineering Piling Hoop 14 with Roller 26423Commercial grade steel. The piling hoop secures around the piling, while roller permits smooth up and down movement. 22.5" Width.

Tiedown Engineering Pipe Holder 3" Comm. Grade 26411K. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set "M" required for attaching.

Tiedown Engineering Pipe Holder-Outside 3" Std 24280K. Bolts to outside of dock. Uses 2" pipe to hold dock in place. Carriage bolt set "M" required for attaching.

Tiedown Engineering Rack Canoe 86924The Canoe Rack provides a sturdy platform for storing a single canoe beside your dock or deck without taking up any surface area. Consists of two mounting arms that will facilitate easy loading, unloading and storage...

Tiedown Engineering Receiver Clamp with Beam 86900The Clamp Style Receiver easily slides onto the bottom rail of truss style docks and is secured in place by tightening set screws.It is easy to install and remove, allowing you to easily relocate the...

Tiedown Engineering Receiver Clamp with Beam 86918The Clamp Style Receiver easily slides onto the bottom rail of truss style docks and is secured in place by tightening set screws.It is easy to install and remove, allowing you to easily relocate the...

Tiedown Engineering Receiver Slotted with Beam 86919The Slotted Style Receiver with the cross beam mounting bracket provides a secure mounting solution for solid side rail docks.The assembly mounts on the side rails of solid rail style docks and is...

Tiedown Engineering Rod Holder 86909The Rod Holder provides secure mounting for up to three fishing rods. The rod holder support arm is pre-drilled with four holes with bolting dimensions of 1-5/16" by 3-3/16". Requires 1 receiver. Rod holders not...

Tiedown Engineering Rod Holder 86927The Rod Holder provides secure mounting for up to three fishing rods. The rod holder support arm is pre-drilled with four holes with bolting dimensions of 1-5/16" by 3-3/16". Requires 1 receiver. Rod holders not...

Tiedown Engineering Soft Anchor Chain 1/4" X 6' 95110Attach between your anchor line and anchor for safe anchoring. Helps keep the anchor shank low and allows the flukes to further penetrate. Also guards against line chafe.

Tiedown Engineering Super Hooker Anchor A good choice for your anchoring needs. Super Hooker anchors are well made, strong and have a hot dipped galvanized finish.

Tiedown Engineering Tii3000 Danf Deepset II Anchor 94031Features precise fluke to shank angles that permit the Deepset II to set the first time, every time, under virtually any condition. Manufactured with premium Chrome molybdenum steel, which can...

Tiedown Engineering Washer Plate Commercial Grade 26409I. Should be used with every Angle. Two required for each Angle. 1-1/2"L x 5"H.