Dock

Tiedown Engineering Chain Holder 26529J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/4", 3/8" and 1/2" chain. 5"L x 5"H.

Tiedown Engineering Chain Holder Injin 26410J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/4", 3/8" and 1/2" chain. 5"L x 5"H.

Tiedown Engineering Cleat Angle 26422F. Should be used for all cross supports.

Tiedown Engineering Connector Pin Set 26531 P. Used for quick disconnect of male and female connectors. Galvanized 3/4" connector pin and hitch clip pin.

Tiedown Engineering Cross Beam 28' Extension 86916With the addition of the Cross Beam 28" Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam...

Tiedown Engineering Cross Beam 28' Extension 86934With the addition of the Cross Beam 28" Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam...

Tiedown Engineering Dock Hdw (M) Car.Bolt Set 8/Bg 26534Used to attach A thru K component parts. 3/8 x 2-1/2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3".

Tiedown Engineering Dock Hdw (N) Hex Head 8/Bag 24279N. Includes lock nut. Used to connect male and female connectors.Galvanized 3/4" x 3-1/2".

Tiedown Engineering Dock Hdw Car Bolt Setinmin 8/B 26535Used to attach A thru K component parts. 3/8 x 2-1/2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3".

Tiedown Engineering Dock Hdw Lag Bolt 3/8X3 8/Bag 24289Bolt and flat washer hot dip galvanized used to attach flotation drums to dock system.

Tiedown Engineering Dock Hdw Lag Bolt 3/8X5 8/Bag 24292Bolt and flat washer hot dip galvanized used to attach flotation drums to dock system.

Tiedown Engineering Female T Connector Ingin 26407G. Bolts to side of dock to attach fingers and ramps.

Tiedown Engineering Female T-Connector 26528G. Bolts to side of dock to attach fingers and ramps.

Tiedown Engineering HD Deck Plate 26416Heavy duty deck plate for use with Piling Hoop. This 3/16" thick 4"x 6" x 22" plate can be bolted from the top and side of the dock. The hoop can then be bolted...

Tiedown Engineering HD Inside Corner 2" Inein 26405E. Should be used with one of the outside corners and has an internal pipe holder. 8-1/4"L x 5"H. Requires carriage bolt set "M" for attaching.

Tiedown Engineering HD Inside Corner Indin 26403D. Should be used with one of the outside corners. Each leg has elongated holes for easy fit.

Tiedown Engineering HD Outside Corner (End) Incin 26402C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners.

Tiedown Engineering HD Outside Corner (Female) Ina 26400A. Two 1/2" welded tabs. Use with a male outside corner.Each leg is 10"L x 5"H.

Tiedown Engineering HD Plate Hoop Roller 26415Piling hoop & roller intended for areas with a lot of wind, current or tidal action. Combines the Piling hoop (26412) and roller assembly (26414) to make...

Tiedown Engineering Hdinside Corner 3" Inein 26404E. Should be used with one of the outside corners and has an internal pipe holder. 8-1/4"L x 5"H. Requires carriage bolt set "M" for attaching.