Anchoring & Docking

Tiedown Engineering Angle Brackets 4X8 26397F. Should be used for all cross supports.

Tiedown Engineering Back Up Plate 26413Q. Reinforcing plates are used to back up single T males and females. 5" x 5".

Tiedown Engineering Chain Holder 26529J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/4", 3/8" and 1/2" chain. 5"L x 5"H.

Tiedown Engineering Chain Holder Injin 26410J. Bolts to side of dock. Use weights and chain to hold dock in place. Accommodates 1/4", 3/8" and 1/2" chain. 5"L x 5"H.

Tiedown Engineering Cleat Angle 26422F. Should be used for all cross supports.

Tiedown Engineering Connector Pin Set 26531P. Used for quick disconnect of male and female connectors. Galvanized 3/4" connector pin and hitch clip pin.

Tiedown Engineering Cross Beam 28' Extension 86916With the addition of the Cross Beam 28" Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet...

Tiedown Engineering Cross Beam 28' Extension 86934With the addition of the Cross Beam 28" Extension, the cross beam used in the Clamp Receiver with Cross Beam or the Slotted Receiver with Cross Beam can be lengthened for use on docks that are six feet...

Tiedown Engineering Danforth 3/8X6 SS Chain with Shackle 95226Package 316 stainless chain with shackle.

Tiedown Engineering Danforth Anchor Kit For 8S 95096Traditional holding power which has always been associated with Danforth Standard Anchors. The shank is made of high strength steel. The steel flukes are strong and wide. Each anchor has a hot dipped...

Tiedown Engineering Dock Hdw (M) Car.Bolt Set 8/Bg 26534Used to attach A thru K component parts. 3/8 x 2-1/2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3".

Tiedown Engineering Dock Hdw (N) Hex Head 8/Bag 24279N. Includes lock nut. Used to connect male and female connectors.Galvanized 3/4" x 3-1/2".

Tiedown Engineering Dock Hdw Car Bolt Setinmin 8/B 26535Used to attach A thru K component parts. 3/8 x 2-1/2" bolt, flat washer and nut. Hot dipped galvanized. Commercial grade 1/2" x 3".

Tiedown Engineering Dock Hdw Lag Bolt 3/8X5 8/Bag 24292Bolt and flat washer hot dip galvanized used to attach flotation drums to dock system.

Tiedown Engineering Female T Connector Ingin 26407G. Bolts to side of dock to attach fingers and ramps.

Tiedown Engineering Female T-Connector 26528G. Bolts to side of dock to attach fingers and ramps.

Tiedown Engineering HD Deck Plate 26416Heavy duty deck plate for use with Piling Hoop. This 3/16" thick 4"x 6" x 22" plate can be bolted from the top and side of the dock. The hoop can then be bolted to the deck plate, allowing it to be removed...

Tiedown Engineering HD Inside Corner Indin 26403D. Should be used with one of the outside corners. Each leg has elongated holes for easy fit.

Tiedown Engineering HD Outside Corner (End) Incin 26402C. Use this corner at ends of fingers and docks. Ideal for swim floats and ski jump corners.

Tiedown Engineering HD Outside Corner (Female) Ina 26400A. Two 1/2" welded tabs. Use with a male outside corner.Each leg is 10"L x 5"H.